Ultrasonic cleaning equipment not only has good cleaning effect, but also has low cost, which makes the product widely used. In order to make the cleaning more effective, let's learn what to pay attention to when cleaning.

一、留意把握應用頻率

1、 Pay attention to the application frequency

超聲波清洗設備在應用時，它的頻率留意要在生產廠商說出示的使用手冊提議的范疇以內，不可把頻率調為很大或較小開展清理，以防上時間對該超聲波清洗機導致?lián)p害。另外，超聲設備的超聲波頻率較高時便會使液體內形成的汽泡規格減少，那樣會使清理抗壓強度也相對變?nèi)?。因而，超聲波清洗機生產廠家提議選用中等水平頻率清理為好。

During the application of ultrasonic cleaning equipment, its frequency shall be within the scope proposed in the user manual presented by the manufacturer. It is not allowed to adjust the frequency to large or small for cleaning, so as to prevent damage to the ultrasonic cleaning machine in time. In addition, when the ultrasonic frequency of the ultrasonic equipment is high, the bubble size formed in the liquid will be reduced, which will make the cleaning compressive strength relatively weak. Therefore, the manufacturer of ultrasonic cleaning machine proposes to use medium frequency cleaning.

二、留意運作時間

2、 Pay attention to the operation time

超聲波清洗設備的運作時間要留意操縱適當，一般來講，超聲波清洗設備不應該持續好幾個鐘頭運作。由于該機器設備較長的運作時間很有可能會導致機器設備內部的網紋輥表層及其網穴壁導致?lián)p害。另外，留意在超聲波清洗機完畢運作以后，應當將調整按鍵歸到零位。除此之外，提議客戶應用超聲波清洗設備以前將較難清理的零件歷經預備處理系統軟件解決后，再放進超聲設備中清理為宜，那樣機器設備運作時間大幅度減少。

The operation time of ultrasonic cleaning equipment should be properly controlled. Generally speaking, ultrasonic cleaning equipment should not last for several hours. Due to the long operation time of the machine and equipment, it is likely to cause damage to the anilox roll surface and its mesh hole wall inside the machine and equipment. In addition, note that after the operation of the ultrasonic cleaning machine, the adjustment button should be set to zero. In addition, it is suggested that before the application of ultrasonic cleaning equipment, the parts that are difficult to clean should be put into the ultrasonic equipment after being solved by the preparatory processing system software, so that the operation time of the machine and equipment will be greatly reduced.

三、留意查驗清理的商品

3、 Pay attention to check the cleaned goods

超聲波清洗設備清理的實質并不是靠震動來做到清理的目地，震動只是是超聲波換能器在工作中時需造成的副產物。超聲波清洗對質量密度越高的被清理物能造成共震的實際效果，因此要是是沒有暇疵的物件，一般的微震不容易造成不好影響。

The essence of ultrasonic cleaning equipment cleaning is not to achieve the purpose of cleaning by vibration. Vibration is only the by-product of ultrasonic transducer in work. The higher the mass density of the object is, the higher the effect of ultrasonic cleaning is. Therefore, if there are no defects in the object, the general micro shock is not easy to cause bad effects.